LIS接口手册CS - 800软件设置第一步(打开系统设置-LIS设置，图1):图1第二步 设置(图2)1.使用l图2第三步:点击保存按钮，保存设置，退出软件。Software instructionsManually send results to LIS:Step 1:Step 2 Click the button “Send LIS Data”, the window as shown:Step 3 :Enter the Strat S. No. and the End S. No., then click the button “Send”.Search Communication Log :Click the button “Comm log”, the window as Shown:Apply the test from LIS:Sample No mode:Step 1 :Step 2 :Click the button “Request LIS Data”, the window as shown :Step 3 :Please put into the range of the samples number and the number of beginning,then press application button. 1-80 normal test position，E81-E90emergency position，one time only can apply one sample.Enter the Sample No. range, then click the button “Requistion”.Sample ID Mode :Step 1 :Step 2 :Manually Apply the test from LIS:Click the button “Requistion LIS Data”, the window as shown :Enter the barcode value, then click the button “Requistion”.Automatic Apply the test from LIS:Step 1Click the button “Sample Barcode Scan”, the window as shown :Enter the scan range, then click the button “Scan”.When the CS-800 finish the scanning, the window as shown :Click the button “OK”, then Apply the test from LIS.Note : The barcode value of “?”, not to LIS transmission.BASIC LIS RELATED TERMS 1. Control CodesLF (Line Feed) (Hex 0A) CR (Carriage Return) (Hex 0D) STX (Start of Text) (Hex 02) ETX (End of Text) (Hex 03) EOT (End of Transmission) (Hex 04) ENQ (Enquiry) (Hex 05) ACK (Acknowledge) (Hex 06) NAK (Not Acknowledged) (Hex 15) 2. Message Frame / Checksum CalculationThe end frameSTX FN Text first char. . Text last char. ETX CH CL CR LF STXis the ASCII code 2, indicating the beginning of a frame transmission.FNis the frame number modulo 8. Frames of a single Transmission Phase areconsecutively numbered beginning with 1. So FN runs from 1 to 7,continues with 0, 1 and so on. Use ASCII codes for the digits 0 to 7 (48-55)!Text is the data content of a frame.ETXis the ASCII code 3, indicating the end of the text block of an end frame.CH, CLrepresent the high nibble (= most significant 4 bit) and the low nibble(=least significant 4 bit) of the 8 bit checksum, respectively. CH and CL are represented as two digits of hex numbers. The checksum is the modulo 8 of the sum of ASCII values of the frame characters starting with and including FN and completing with ETX.Example for Checksum CalculationSTX1TestETXSymbolCharacterValue (decimal)SumSTX STX 002 0 FN 1 049 49 Text T +084 133 e +101 234 s +115 349 t +116 465 ETX ETX +003 468 468 = 468 MOD 256 212 = 212 CH D 068 CL 4 052 CR CR 013 LF LF 010 to be sent:STX1TestETXD4CRLFChecksum is sum of transmitted character codes including from FN to ETX modulo 100 hex. It is an 8 bit value expressed and transmitted as a two digit hex number, most significant digit first.3. DelimitersThe Presentation Layer uses some characters as special delimiter codes. These characters may not be used as normal message text:Delimiter Character Char. ASCII decimal ASCII hex. Record delimiter = carriage return 13 0Dh Field delimiter = vertical bar | 124 7Ch Repeat delimiter = backslash 92 5Ch Component delimiter = caret 94 5Eh Escape delimiter = ampersand & 37 26h 4. Table of Record Message TypeRecord Name Identifier Message Header Record H Patient Information Record P Test Order Record O Result Record R Message Terminator Record L Request Information Record Q 5. Communication modeCS-800 is able to communicate in realtime mode or batch mode.Realtime Mode: The instruments identifies a sample identification or a Disk/positionidentification and asks the host for test selections.Results will be uploaded as soon as available and/or as manuallyselected from the result data base.Batch Mode: Results will be uploaded as soon as available and/or as manuallyselected from the result data base.6. Sample No. and ID ModesThe analyzer can be operated in one of two modes for identifying samples:1. Sample No. Mode 2. ID ModeThe most common mode used is ID Mode, which has provisions for processing samples that have damaged, unreadable or missing barcode labels. The user canswitch betwee