连供系统问题集合（Even a collection of system problems）Epson R210 and R230 for system problem setsAt present, Epson R210 and R230 are the machines with the most users. The machine printing accuracy is high, but there are several problems.1. Bad questions of Epson R210 and R230Playing like paper is not a big problem, playing card paper has a certain problem, poor ink jet paper problem is even bigger.Reason of failure: because the paper of printer basically has coating, cheap card paper and inkjet paper coating craft is very bad! The user can wipe with his finger, and he will find the coated powder falling, which is why the paper is slipping.Solution: so users must first use a good paper medium for a few months while using R210 and 230.You can choose the quality of the card paper. I just recommend good consumables to my friends.Special note: the first installation of a connected customer please noteA, the most important problem of continuous supply of ink system with Epson210 and 230 is that the outer cartridge must be placed in the same horizontal plane of the printer! (putting the outer box at a higher position than the printer results in ink leaking to the print head, which is a serious mistake!)B, remember to open the vent and replace the filter, which is the easiest way for first-time customers to forget the operation!C. When fixing the pipe, pay attention to the center, so that the pipe will swing back and forth to work at a minimum, and control the line failure within the minimum range!The solution to the Epson210, 230 that has just been installed to provide for the peace with horizontal stripes:What literally put paper into the printer, the paper simulate choose high quality glossy photo paper, print quality choose photos RPM, print out of the horizontal grain color pictures, more general print a 2-3 pieces of A4 paper, turn back to choose high quality photos, basic can solve horizontal stripes.Print high quality photo Settings: 1. High quality photo paper; 2. Select RPM; 3. Turn off high-speed printing.2. EpsonR210 and 230 twinkle light have several kinds(1) the line will not flow smoothly and the lamp will flash this kind of solution. Everyone will adjust the length of the pipeline. Too long will run into the wall, too short will hold the print head, then the red light will flash;(2) the grating band will also double light. This can be done by rubbing toilet paper with water.(3) its OK to use the software to clear 0.(4) is the double light that everyone has the most headache. If its the same frequency, this is the most troublesome, its possible to tear down the machine. One reason is that the software that detects ink is not used to create a lock machine.Solution: 1. No software to detect ink; 2. There is no special case for the inner box for supply.Solution to the problem: 1. 2. Put the original cartridge into cartridge decoding.The machines of Epson210 and 230 are easy to disarm, and the people behind the repair station cant see it. A rose was spun off behind the machine. Other places can be done with hands. Just a few CARDS. Then the guide is removed and the car is removed. The clean sensor is OK. Sometimes the ink will corrode the sensing line.Some experience of troubleshooting:Take anything out of the machine, make sure to see it clearly, carefully restore the original, do not leave tail even a small change can lead to unexpected failure;Two, the fault appears must find out its reason, otherwise want to return to work again (if my first time disassembly to find out the reason, wont have the second time disassembly machine). The sensor is dirty is not necessarily teardown (too much), know the region and the structure of it, turn it off, usable cotton cloth or cotton paper on finger volume from the left of the stretch into a crack to wipe, general can clean it. If its ink blisters the whole sensor is nondisassembly.Solutions to sensor problems:Ink is water-based, and water should be rubbed off, but its better not to use alcohol. The sensor is stained with ink. It must be taken apart to clean it. An easy way to do this without having to open the machine is:1. Press the ink key after startup2. Unplug the power3. Move the inking truck back and forth, with a screw on the left side of the ink-car, and a lot of lines can be seen. With the narrowest one, choose it to find the bottom - the head, you can see the protruding material, the cotton is stained with pure water to clean back and forth, you will find that there is ink; Well, lets do it a couple of times, our experience, three times.Another good way to do that is to put the cotton in the place where the ink-car moves, move the ink and clean the sensors ink.If you cant do it, youll have to do the last one.The parts of EpsonR210 and 230 are:1, shell2. On the left of the machine, two card spring, one spring (th