UserGuideManual,Motor Drive Vertical Mount FormerBT-100F BT-201F手动,电动带式电子零件成型机使用说明书 深 圳 市 新 比 特 电 子 科 技 有 限 公 司Tel:0755-27381636 27349620 27382501 Fax:0755-27382481Http:/www.xinbite.com Email:sdxxinbite.com 非常感谢并恭喜您拥有本公司BT-100F手动电子零件成型机，BT-201F电动电子零件成型机。在开始使用之前，请检查包装中以下项目是否完整。1、 本体2、 把手3、 零件成品盒4、 带装零件支架安装您的机械：1、 将手柄装在机械本体上。2、 把机械置于桌边并固定于其上。3、 把带装零件固定架装于本体的边上（在本体之两边均有双孔可选择）4、 把成品盒置于机械的下方。现在您可以开始设定您的机械了。操作程序：1、 把带装零件滑过进料轨道（28），并注意不要太紧，把零件本体置于成型齿轮（22）右边（如图Fig4）并先试弯一个看是否符合您的规格。2、 调整零件脚距先松开成型齿轮（22）上的固定螺丝，调整成型齿轮（22）与成型弯刀（23）之间的间隙，使其达到所需要的脚距（调整完后记得锁紧固定螺丝）。3、 调整零件脚长度先松开切断齿轮（221）上的固定螺丝，然后调整所需要的长度（调整完后记得锁紧固定螺丝）。4、 调整零件肩高零件本体（301）距离成型齿轮（22）约1mm左右，视本体大小而定，距离越大弯出来高度越高（以不伤到零件本体为原则）现在您的机械可以开始使用了BT-100F顺时钟方向转动把手，您会看到零件成型弯脚后一个个掉入成品盒中，捡几个检查一下，如果规格不符，请照上述调整方式修正，如果规格符合即可正式生产。BT-201F先把调速器（162）转到零，插上电源并打开马达开关（161）慢慢加快调速器（162）到适当速度，并检查成型后之规格，如符合即可正式生产。经过使用一段时间之后，如果您发现机械所切出来的脚有毛边时，请把切断刀（21）拆下来加以研磨，或向本公司购买备品，不要忘了定期给机械加润滑油及清理，如有不清楚之处，请联络经销商或本公司客服部，我们很乐意为您服务。1Your machine comes complete with the following items in the list below.Make sure that you have evetything betore trying to set up your unit.1. Main Body2. handle3. Parts Bin4. Tape Reel Holder BaySetting Up Your Machine1. Assemble the handle to the main body 2. Put the unit along the side of the bench and fix it onto the bench.3. Assemble the tape reel holder on the machine.There are two sets of holes on both sides of the base that you can choose to mount it.4. Put the parts bin under the machine.Now it is ready for adjustment.Operation Procedure1. Sliding the taped components into the plastix Feeding fuide(28),Please note to make it freely not too tight.Then engaging the lead of components to the forming wheel(22)and put the body to the right side of the forming wheel as illustrared in FIG-5.Cranking the handle to test the forming condition.2. Adjusting the Pitch of the components.Release the fised screws in the forming wheel(220,Adjusting the distamce between the forming wheel(22)and Bending Plate(23)to the desired specification(Pleasedont forget to right the screw released.)3. Adjusting the length of the components.Release the fixing screws of the cutting Disc and adjusting the distance to meet the requirement(tighten the ssrew released.)4. setting the Shoulder Height of the componentsOne(!)mm is a normal distance between the body of components to the forming wheel(22).More distance will get more height in the shoulder of the components(Basing on the principle of no damage of the body)Your Machine Is Ready For Running Now*100F Cranking the handle of the machine clockwise slowly.You will see some components that are cut and drop into the parts bin.Take some and check.Please re-adjusting the machine according the procedure if failed to meet specification.Otherwise the machine is ready for mass production.*201F Turning the speed regulator(162)to Zero(0)position before tutn on the ON/OFF Power Switch().Then increasing the speed gradually when the power is ON unat proper speed is reached.Take some of the parts formed and check the specification.Re-adjusting the data according to procedure listed or the machine os ready for mass production.If the cutting edge of the lead is not good as before after a long time operation or burr is fouvd, please dismantle the cutting blade and re-sharpen it Dont forget your regular lubrication and maintenance.If further service is needed.Please call our agent or contact us directly.2Spare Parts List零件表Part No.Description品 名14Parts Bin成品盒16Side Wall右主机板161Power Switch电源开关162Speed Regulator调速器163Main Body圆形本体17Side Wall(L)左主机板171Bearing Ring,Main Shaft主轴培林座172Base脚座21Cutting Disc Assembly切刀210Shaft,Cutting Dise切刀轴22Forming Wheel成型齿轮221Cutting Wheel Assembly切断齿轮222Main Shaft主轴23Bending Plate成型弯刀231Bending Plate Blick成型刀座232Screw,Bending Plate弯刀固定螺丝233Shaft,Bending Plate弯刀导杆25Frame支架26Motor马达26AHandle把手260Motor Gear马达齿轮261Main Shaft,Motor马达主轴262Frame,Motor马达支架28Feeding Guide带装进料轨道281Square Bar方型轴282Fix Screw,Feeding Guide轨道固定螺丝283Components Remove料架器29Bar,Tape Reel Holder料架杆290Roller,Tape Reel Holder料架轮291Shaft,Tape Reel Holder料架轴292Spring,Tape Reel Holder弹簧293Knob,Tape Reel料架固定螺帽3