资源预览内容
第1页 / 共5页
第2页 / 共5页
第3页 / 共5页
第4页 / 共5页
第5页 / 共5页
亲,该文档总共5页全部预览完了,如果喜欢就下载吧!
资源描述
模具英语专业术语模具的分类:冲压模(五金模): stamping die分离模: cutting die成形模: forming die塑胶模: plastics mold注射模: injection mold压缩模: compression mold铸塑模: transfer mold吹塑模: blow mold吸塑模: suck mold铸造模: casting die砂型铸造: sand casting压铸模: die casting锻造模: forging die塑胶模具术语 一、入水:gate 进入位(入水点): gate location 水口形式: gate type 大水口(侧浇口): edge gate 潜水口: sub-gate薄膜式水口: film gate牛角式潜水口: banana gate扇形水口: fan gate环形水口: ring gate二次水口: 细水口: pin-point gate 水口大小: gate size 转水口:switching runner/gate 唧嘴口径: sprue diameter直接水口: direct gate 二、流道: runner 热流道: hot runner,hot manifold 热嘴冷流道: hot sprue/cold runner 唧嘴直流: direct sprue gate 圆形(整圆/半圆)流道: round(full/half) runner 矩形流道: rectangle runner梯形流道: trapezoid runnerU形流道: U shape runner 流道电脑分析(模流分析): mold flow analysis 流道平衡: runner balance 热嘴: hot sprue/tip 热流道板:hot manifold 发热管:cartridge heater 探针: thermocouples 插头:connector plug 插座: connector socket 密封/封料: seal 三、运水:water line 喉塞:line plug 喉管:tube 塑胶管:plastic tube 快速接头:jiffy quick connector plug/socket 四、模具零件:mold components 三板模(细水口模):3-plate mold 二板模(大水口模):2-plate mold热流道模具: hot-runner/manifold mold 叠层模: stacked mold边钉/导边:leader pin/guide pin 边司/导套:guide pin/guide bushing直导套:shoulder guide bushing有托导套:straight guide bushing中托司: ejector guide bush中托边: ejector guide pin 回针: return pin面板: top clamp plateA板: A plate推板:stripper plateB板: B plate托板: support plate方铁: spacer block加高方铁: higher spacer block顶针固定板:ejector retainner plate 顶针板:ejector plate 底板: bottom clamp plate螺丝: screw 杯头螺丝: socket cup head screw平头螺丝: socket flat head screw机米螺丝:外六角头螺丝: bolt栓打螺丝(等高螺丝):S.H.S.B管钉:dowel pin 开模槽:ply bar socket 内模管位(模仁互锁):core/cavity inter-lock 顶针:ejector pin 司筒:ejector sleeve 司筒针:sleeve ejector pin 缩呵:movable core,return core, core puller 扣机(尼龙拉勾):nylon latch lock 斜顶:lifter 模胚(架): mold base 上内模:cavity insert 下内模:core insert 行位(滑块): slide 行位扣:镶件:insert 压座/斜鸡:wedge 耐磨板/油板: wear plate 压条:gib 撑头: support pillar 唧嘴: sprue bushing 挡板:stop plate 定位圈(法兰):locating ring 锁扣(模锁):latch 扣鸡:parting lock set 推杆:push bar 顶板:eracuretun 活动臂:lever arm 分流锥:spure sperader 水口司:bush 垃圾钉:stop pin 隔片:buffle 弹弓柱:spring rod 弹弓:die spring 型腔(前模仁): cavity型芯(后模仁): core镶针:insert pin 销子(销钉):dowel pin 波子弹弓:ball catch 喉塞(堵头): pipe plug 锁模块:lock plate 斜顶杆:angle ejector rod 斜顶针:angle from pin尼龙拉勾:parting locks 活动臂:lever arm 复位键、提前回杆:early return bar 气阀:valves 斜导边(斜导柱):angle pin 油缸: hydraulic cylinder液压马达: hydraulic motor齿轮: gear轴承: bear术语:terms 承压平面平衡:parting surface support balance 分模面排气:parting line venting 回针碰料位:return pin and cavity interference 模总高超出啤机规格:mold base shut hight 顶针碰运水:water line interferes with ejector pin 料位出上/下模:part from cavity (core) side 模胚原身出料位:cavity direct cut on A-plate,core direct cut on B-plate. 不准用镶件: Do not use (core/cavity) insert 用铍铜做镶件: use beryllium copper insert 初步模图设计:preliminary mold design 正式模图设计: final mold design反呵:reverse core 弹弓压缩量:spring compressed length 稳定性好:good stability,stable 强度不够:insufficient rigidity 均匀冷却:even cooling 扣模(粘模):sticking 顶白: stress mark热膨胀:thero expansion 缩水: shrinkage物料表: BOM原料: raw materials物料: materials工程试模材料: material for engineering mold testing成品: finished product 半成品: semi-finished product 公差:tolorance 铜公(电极):copper electrode射料不足: short shot缺口: nick 瑕疪(斑点): speck 亮斑: shine 银纹: splay 焦痕: gas mark 起鳞: delamination 冷块: cold slug 导色: blush 沟槽;凿槽: gouge 段面咬花: satin texture 证示线: witness line 专利: patent 沙砾: grit 细粒: granule=peuet=grain 抽粒机: grit maker 缓冲: cushion 不锈钢: stainless steel镁铝合金: magnalium 镁金属: magnesium 钣金: metal plate 车/车床: lathe 铣床/铣床: mill 刨/刨床: plane 磨/磨床: grind 钻/钻床: drill 镗: boring 气泡: blinster版次: revision 备注: remark 生产确认: production control confirmation 初审: checked by 核准: approved by 部门: department电镀: plate 成型: molding 样品: sample 雕刻: engrave蚀纹: texture加硬: harden热处理: heat treatment淬火: quenching 回火: tempering 退火: annealing 碳化: carbonization铬酸处理: chromate 阳性处理: anodize氮化: nitrifying
网站客服QQ:2055934822
金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号