1 FS0000F DFM Report DFM Engineer LIMIN Approved Date 2014 02 26 DFM Design For Manufacture Project name 2 Mould No FS0000E Customer Name UKAG Customer mould No 请客人提供 Part No Screen Side Frame Cavities1 1 Material PC ABS BAYER T65XF Size for 1 part 182 7X126 9X3 5 Inch mmmm 产品信息 Product Information 3 开 模 客 供 资料 information to be provided by customer 序号资料名称Name 内 容 Description 收到日期 Received date 备注 remarks 1 胶 料 resin PC ABS BAYER T65XF 2014 02 25 2 缩 水 率 hrinkage 请客人提供 我们选定为0 005 请客人确认或提供 3 啤机吨位 Press tonnage 请客人提供啤机 的相关信息 4 设计标准customer tooling standard 请客人提供 5 胶料特性 resin date sheet 请客人提供 开模时需要收到的客供资料 4 上下模分析 CAV COR Customer comment please give your approval and comments Date Approval by RemarkOK or NG cavity side core side 5 进浇口建议 Gate Advice 方案一 冷流道 两点潜水入胶 170mm 冷流道 潜水入胶 优点 不需热流道板 缺点 流道长 注塑压力大 模具排位 模胚尺寸为5565 6 进浇口建议 Gate Advice 方案二 推荐 Customer comment please give your approval and comments Date Approval by RemarkOK or NG Moldmaster 1 open nozzle HRM Sub Gate Hot Sprue Sub Gate 由于产品较大 同时根据排位需要 我们建议客人每个产品用一个热转冷流道 两点潜水 请客人确认热嘴的型号并确认是否需要订购接线盒 并提供具体品牌及型号 接线方式 同时 请客人确认另一个产品是否为完全镜像关系 请市场考虑增加热嘴报价 热嘴转冷流道潜水入胶 优点 流道短 注塑压力小 产品填充好 缺点 需要热流道板 模具成本相应增加 模具排位 模 胚尺寸为5565 7 Customer comment please give your approval and comments Date Approval by RemarkOK or NG 结构分析 Structure analysis StructureQuantity Slide1 Lifter0 Collapasible core Core slider 01 C C C C见下页 8 Customer comment please give your approval and comments Date Approval by RemarkOK or NG 结构分析 Structure analysis Core side ST1 8 ST2 20 8 SECTION C C 自制定位零件 底部加弹弓 9 Customer comment please give your approval and comments DateApproval by RemarkOK or NG 镶件分析 Insert analysis Cavity Insert 做浮动镶件 避免产品粘前 模 10 10 Customer comment please give your approval and comments DateApproval by RemarkOK or NG Core Insert 下模三个镶件 每个 镶件上下两支扁顶针 11 Customer comment please give your approval and comments Date Approval by RemarkOK or NG Core side 顶针 EJECTOR PIN STRAIGHT BAR STRIPPER BAR 12 分型线分析 PL analysis Customer comment please give your approval and comments Date Approval by RemarkOK or NG 行位分型线需移到此处 与前模做3度的插穿 角 13 分型线分析 PL analysis Customer comment please give your approval and comments Date Approval by RemarkOK or NG 此面插穿角不够 需 修到3 5度 两处 一处 为了更好的封胶 此处的插 穿距离尽可能修到2 5MM以 上 14 分型线分析 PL analysis Customer comment please give your approval and comments Date Approval by RemarkOK or NG 为简化加工及分型 指示处减 胶0 03MM 出后模 15 擦穿位置分析 Shut off position Customer comment please give your approval and comments Date Approval by RemarkOK or NG 此面插穿角不够 需 修到3度 16 擦穿位置分析 Shut off position Customer comment please give your approval and comments Date Approval by RemarkOK or NG 此面插穿角不够 需 修到3度 17 产品出模分析 Product Draft analysis Customer comment please give your approval and comments Date Approval by RemarkOK or NG Draft analysis Draft OK 18 产品料厚分析 Product Thickness analysis Customer comment please give your approval and comments Date Approval by RemarkOK or NG 产品胶料厚度均匀 19 产品光洁度标准 NO Texture 请提供光洁度标准 Customer comment please give your approval and comments Date Approval by RemarkOK or NG 20 1 版本号我司做镶针 相关的字体我司默 认为晒字 深0 2MM 凸字 日期镶件 年月一起 Engraving Others Customer comment please give your approval and comments Date Approval by RemarkOK or NG 21 模具排位 Mould overall dimensions Mold overall layout EJ SIDE PLAN VIEW 550 650 模胚已超报价 4045 请客 人确认是否合适啤机 同时 市场考虑是否增加报价 2222 备注Remark 烦请贵司在我司提供的开模方案上每页做明确回复 同意或不同意 如未作明确回复的部分 我司将视为默认我司方案 我司将按此方 案进行后续工作 Please reply against our PPT in each page OK or Nok if there is no comment in any page of the PPT we will consider it as OK and we will implement the proposal in the PPT THANK YOU