Quick Start SINUMERIK 802D 新一代经济型数控系统 Copyright Siemens Ltd China All Rights Reserved 83 34100 REFP SET POS 0 8 R1 mm degrees 参考点设定位置 RESET 2 2 Always 0 DOUBLE 34110 REFP CYCLE NR 8 R1 返回参考点轴次序 RESET 2 2 Always 1 1 5 DWORD 34200 ENC REFP MODE 0 8 R1 参考点模式 POWER ON 2 2 Always 1 0 7 BYTE 34210 ENC REFP STATE 0 8 R1 绝对值编码器调试状态 IMMEDIATE 2 2 Always 0 0 2 BYTE 34220 ENC ABS TURNS MODULO 6 R2 旋转绝对值编码器 Modulo 区 POWER ON 2 2 Always 4096 1 4096 DWORD 34990 ENC ACTUAL SMOOTH TIME 0 5 s 实际值平滑时间常数 POWER ON 2 7 Always 0 0 0 0 0 0 0 5 DOUBLE 35000 SPIND ASSIGN TO MACHAX 5 S1 定义机床轴为主轴 POWER ON 2 2 Always 0 0 1 BYTE 35010 GEAR STEP CHANGE ENABLE 5 S1 齿轮换档生效 POWER ON 2 2 Always 0 BOOLEAN 35012 GEAR STEP CHANGE POSITION 0 5 5 S1 mm degrees 齿轮换档位置 NEW CONF 2 7 Always 0 0 0 0 0 0 0 plus DOUBLE 35020 SPINDLE DEFAULT MODE 5 S1 主轴基本方式 0 1 速度控制 2 定位方式 3 坐标方式 RESET 2 7 Always 0 0 3 BYTE 35030 SPINDLE DEFAULT ACT MASK 5 S1 HEX 主轴基本方式生效时间 0 上电 1 程序启动 3 复位 M02 M30 RESET 2 7 Always 0 x00 0 0 x03 BYTE 35040 SPIND ACTIVE AFTER RESET 5 S1 主轴复位后自动恢复 POWER ON 2 2 Always 0 BOOLEAN 35100 SPIND VELO LIMIT 5 S1 Rpm 最高主轴速度 POWER ON 2 7 Always 10000 0 DOUBLE 35110 GEAR STEP MAX VELO 0 5 5 S1 Rpm 主轴各档最高转速 NEW CONF 2 7 Always 500 500 1000 2000 4000 8000 DOUBLE 35120 GEAR STEP MIN VELO 0 5 5 S1 Rpm 主轴各档最低转速 NEW CONF 2 7 Always 50 50 400 800 1500 3000 DOUBLE 35130 GEAR STEP MAX VELO LIMIT 0 5 5 S1 Rpm 主轴各档最高转速限制 NEW CONF 2 7 Always 500 500 1000 2000 4000 8000 DOUBLE 35140 GEAR STEP MIN VELO LIMIT 0 5 5 S1 Rpm 主轴各档最低转速限制 NEW CONF 2 7 Always 5 5 10 20 40 80 DOUBLE 35150 SPIND DES VELO TOL 5 S1 主轴转速容差 RESET 2 2 Always 0 1 0 0 1 0 DOUBLE Quick Start SINUMERIK 802D 新一代经济型数控系统 84 Copyright Siemens Ltd China All Rights Reserved 35160 SPIND EXTERN VELO LIMIT 5 S1 Rpm PLC 主轴速度限制 NEW CONF 2 7 Always 1000 0 DOUBLE 35200 GEAR STEP SPEEDCTRL ACCEL 0 5 5 S1 Umdr s 2 开环模式各档加速度 NEW CONF 2 7 Always 30 0 30 0 25 0 20 0 15 0 10 0 0 001 DOUBLE 35210 GEAR STEP POSCTRL ACCEL 0 5 5 S1 Umdr s 2 位置环模式的加速度 NEW CONF 2 7 Always 30 0 30 0 25 0 20 0 15 0 10 0 0 001 DOUBLE 35300 SPIND POSCTRL VELO 5 S1 Rpm 主轴位置控制速度 NEW CONF 2 2 Always 500 0 DOUBLE 35310 SPIND POSIT DELAY TIME 0 5 5 S1 s 主轴定位延时时间 NEW CONF 2 2 Always 0 0 0 05 0 1 0 2 0 4 0 8 DOUBLE DOUBLE 35350 SPIND POSITIONING DIR 5 S1 主轴定位转动方向 RESET 2 2 Always 3 3 4 BYTE 35400 SPIND OSCILL DES VELO 5 S1 Rpm 主轴摆动速度 NEW CONF 2 2 Always 500 0 DOUBLE 35410 SPIND OSCILL ACCEL 5 S1 Umdr s 2 主轴摆动加速度 NEW CONF 2 2 Always 16 0 001 DOUBLE 35430 SPIND OSCILL START DIR 5 S1 主轴判断起始方向 RESET 2 2 Always 0 0 4 BYTE 35440 SPIND OSCILL TIME CW 5 S1 S 主轴正向摆动时间 NEW CONF 2 2 Always 1 0 DOUBLE 35450 SPIND OSCILL TIME CCW 5 S1 S 主轴负向摆动时间 NEW CONF 2 2 Always 0 5 DOUBLE 35500 SPIND ON SPEED AT IPO START 5 S1 主轴速度达到给定值才能激活进给使能 RESET 2 2 Always 1 0 2 BYTE 35510 SPIND STOPPED AT IPO START 5 S1 主轴停止后才能激活进给使能 RESET 2 2 Always 0 BOOLEAN 35550 DRILL VELO LIMIT 0 5 5 S1 主轴停止后才能激活进给使能 RESET 2 2 Always 0 BOOLEAN 36000 STOP LIMIT COARSE 2 A3 mm degrees 准停定位窗口 粗 NEW CONF 2 2 Always 0 04 DOUBLE 36010 STOP LIMIT FINE 2 A3 mm degrees 准停定位窗口 精 NEW CONF 2 2 Always 0 01 DOUBLE 36020 POSITIONING TIME 2 A3 S 准停精定位延时时间 NEW CONF 2 2 Always 1 0 DOUBLE 36030 STANDSTILL POS TOL 2 A3 mm degrees 零速位置容差 NEW CONF 2 2 Always 0 2 DOUBLE Quick Start SINUMERIK 802D 新一代经济型数控系统 Copyright Siemens Ltd China All Rights Reserved 85 36040 STANDSTILL DELAY TIME 2 A3 S 零速监控延时时间 NEW CONF 2 2 Always 0 4 DOUBLE 36050 CLAMP POS TOL 2 A3 mm degrees 卡紧位置容差 NEW CONF 2 2 Always 0 5 DOUBLE 36060 STANDSTILL VELO TOL 2 A3 mm min rpm 静止速度容差 定义最大轴或主轴的停止速度 NEW CONF 2 2 Always 5 0 mm min 0 01388 rpm DOUBLE 36100 POS LIMIT MINUS 2 A3 mm degrees 第一软限位负向 RESET 2 7 Always 100000000 DOUBLE 36110 POS LIMIT PLUS 2 A3 mm degrees 第一软限位正向 RESET 2 7 Always 100000000 DOUBLE 36120 POS LIMIT MINUS2 2 A3 mm degrees 第二软限位负向 RESET 2 7 Always 100000000 DOUBLE 36130 POS LIMIT PLUS2 2 A3 mm degrees 第二软限位正向 RESET 2 7 Always 100000000 DOUBLE 36200 AX VELO LIMIT 0 5 2 A3 mm min rpm 速度监控的门限值 NEW CONF 2 7 Always 11500 11500 11500 mm min 31 944 31 944 31 944 31 944 rpm DOUBLE 36210 CTRLOUT LIMIT 3 G2 最大速度给定值 NEW CONF 2 7 Always 110 0 0 200 DOUBLE 36300 ENC FREQ LIMIT 0 2 A3 Hz 编码器频率极限 POWER ON 2 2 Always 300000 DOUBLE 36302 ENC FREQ LIMIT LOW 0 8 R1 编码器频率限制低 at which encoder is switched on again hysteresis NEW CONF 2 2 Always 99 9 0 100 DOUBLE 36310 ENC ZERO MONITORING 2 A3 编码器零标记监控 NEW CONF 2 2 Always 0 v DWORD 36400 CONTOUR TOL 2 A3 mm degrees 轮廓监控容差带 NEW CONF 2 2 Always 1 0 DOUBLE 36500 ENC CHANGE TOL 16 K3 mm degrees 位置实际值的切换容差 NEW CONF 2 2 Always 0 1 DOUBLE 36600 BRAKE MODE CHOICE 2 A3 制动特性硬件限位开关 POWER ON 2 2 Always 0 0 1 BYTE 36610 AX EMERGENCY STOP TIME 2 A3 S 急停制动时间 NEW CONF 2 2 Always 0 05 0 02 1000 DOUBLE Quick Start SINUMERIK 802D 新一代经济型数控系统 86 Copyright Siemens Ltd China All Rights Reserved 36620 SERVO DISABLE DELAY TIME 1 N2 S 伺服禁止延时时间 NEW CONF 2 2 Always 0 1 0 02 1000 DOUBLE 36710 DRIFT LIMIT 0 K3 自动漂移补偿的极限值 NEW CONF 2 7 Always 0 0 0 0 plus DOUBLE 36720 DRIFT VALUE 0 S3 漂移基本值 NEW CONF 2 2 Always 0 0 5 0 5 0 DOUBLE 37000 FIX