800-231-0077 14211 Industry Street Houston, TX 77053 TEL: 713-434-0934 FAX: 713-433-6201 eMail: separationsacsind.com Visit our web site www.acsseparations.comTHREEPHASEINGAS OUTGAS OUT20 Ft. Gravity Separator12 Ft. Coalescer Vessel16“INTERFACELEVELTHREE PHASE INLIQUID LEVELLIQUID LEVEL30“36“ ID60“ IDLIGHTPHASEOUTLIGHT PHASE OUTHEAVYPHASEOUTLiquid-Liquid Coalescer Design ManualACS Separations turbulent flow causes remixing. An example of this sizing method in a decanter is contained in Case Study 2, see page 12.In order to settle fine droplets and ensure laminar flow, large vessels and long residence times are required. It may take five, ten, and or even thirty minutes to make a separation, depending on the physical prop- erties of the stream. With the capacity intensification forced on modern refineries and chemical plants and achieved with advanced mass transfer internals, cat- alysts, and heat exchanger designs, operators find that their separators only have half or a third of the time originally anticipated. This results in hazy, off spec products or intermediates that cause problems in downstream equipment. TEL: 800-231-0077 FAX: 713-433-6201 WEB: www.acsseparations.com EMAIL: separationsacsind.comLIQUID-LIQUID COALESCER DESIGN MANUAL1Bouyant ForceInertial Force dViscous Drag ForceFIGURE 1Forces on a light droplet dispersed in a heavy liquidWith Coalescer Media and Internals, unit perform- ance can be restored. Typical applications include: Upgrading 3-Phase Separators and Decanters Removing haze from finished products such as diesel and jet fuel Oil/Water Separators Solvent recovery from liquid/liquid extraction towers Basic Design Concepts The Emulsion In selecting and designing a coalescer, it is important to understand and characterize the emulsion that has to be treated. The finer the droplets dispersed in an emulsion, the more stable it is, because the buoyancy force diminishes in magnitude as the diameter decreases. The manner in which the mixture is created effects the droplet size distribution. For instance, centrifugal pumps shear liquid droplets much more severely than progressive cavity, thereby creating finer droplets. It is also important for the designer to know how much time has elapsed since the mixing/shearing occurred. This is because as time goes on, smaller droplets aggregate (or coalesce) and larger droplets are more likely to have joined a separate layer so that they are no longer considered to be entrained.An important tool to quantify an emulsion is the Droplet Size Distribution Curve generated by plotting the droplet diameters against the volume or mass fraction at that dif- ferential diameter. As stated above, the shape of the dis- tribution is affected by the manner in which the emulsion was formed, and its age. Consider a stream with a fine emulsion (or immature dispersion) as in Figure 2. Overtime, the peak of the volume fraction curve shifts to greater droplet diameters until there are more large droplets than fines.Another key characteristic of an emulsion and the dis- tribution that describes it is the existence of a Maximum Droplet Diameter (1000m in Figure 2). The maximum stable droplet size that an emulsion will develop in a given situation depends on the mechanism of their cre- ation, the amount of energy imparted to the mixture, and the interfacial tension between the phases. Droplets larger than the maximum quickly leave the dispersed phase to form a separate liquid layer and therefore need not be considered part of the emulsion.Generating distributions can be done by collecting and plotting empirical data. Alternately, Mugele and Evans (see General References) showed they have a reliable method for modeling this data as a function of standard deviations that requires only knowledge of the maximum droplet diameter and two different values of the mean. In the typical interconnecting piping between a con- denser and a two or three phase separator; from a centrifugal pump and a distillation column feed coalescer; etc., a dispersion develops to where the Sauter (volume/ area) mean is roughly 0.3 and the mass (volume/ diameter) mean is roughly 0.4 of the max- imum diameter, respectively. A coalescer is often needed, though, for mature distri- butions (when the mean will be larger than a Gaussian 0.5 of the maximum diameter). Examples are the dis- persion of produced water in crude oil that has traveled for weeks in a tanker and the water that has settled in a product storage tank over several days. Therefore, with minimal data, an experienced designer can have an accurate idea of the dispersion that a coalescer must treat.When the average droplet is greater than roughly 1/2 mil- limeter (500 microns), an open gravity settler is appropri- ate. Table 1 shows some typical sources that can generate dispersions that require the use of liquid-liquid coalescers. Also given are some characteristics of the emulsions that are created.TEL: 800-2