Page 1TECHNICAL INFO V300 - 17TO: All AOI engineers, ROMs, RC AOICC: RCSMs, Uri Feldman, Jack Krispin, Rick Jackson, Itzik Tobally EBL, Avi Moses ISL, Izhak Beeri ISL.FROM: Onn TavorDATE: 12/20/95SUBJECT: “asuprm.cnf , config.cnf” - Files ExplanationsMany of the parameters in the above files are not known to many of us. Following requests to clarify the content of these files, attached please find explanation per parameter. For other files explanation refer to the V3.0 Upgrade Manual (sent AOI Update #20 ).Some parameters are defined as not changeable and marked “DO NOT TOUCH”. Reason is the importance of these parameters as fixed values for the software. Do not modify these parameters without prior approval.Regards,Onn TavorAOI Technical Manager_.-.| File : CONFIG.CNF | Version : 02.06 | Creation : 13-Jan-92 | Update : 06-Mar-94 |- ; COMM_BOARD* = ff /* 00 - Not exist , ff - Yes exist. */; NDF = ff /* 00 - Not exist , ff - Yes exist. */; XFIX = ff /* 00 - Not exist , ff - Yes exist. */; DD_CORRECT = ff /* 00 - Dont correct at DishDown ff - Use the DD corection file(/vd/asu/dishdown.msr)*/; DD_AVE_MODE = 7f /* 00 - Max , 7f - Medium , ff - Average . Calculating full scale at DD. */; DD_AVE_FACTOR = 1.0 /* Dish Down average factor: DD full scal = DD full scale * DD_AVE_FACTOR (used in the cases when DD full scale is lower than 95% due to NDF.*/; BOOT_FLAG* = Y /* (DB command) Y - Yes Perform boot on error (the host is sending the DB command to the MUPC/ N - Do not perform boot on error. */; DELAY3* = 7f /* 00 - delay.dat , ff - delay3.dat , 7f - formula.delay between holes & DD due to cables length differances. */; NEW_ADO_FLAG = 00 /* 00 - Old PRD (old FLAD) , ff - New PRD (new FLAD). */; NDF_SHUT_TIME = 300 /* Ndf shut time in seconds. 0 means auto shutter NDF is not activated. */; TF_CONFIG = 00 /* 00 - Not exist, 7f - Exist for calib only, ff - Exist for use. */; AUTO_LSR_UPD = 00 /* 00 - No update , 7f - laser update only , update all. */ Page 2_.-| File : ASUPRM.CNF | Version : 02.60 | Creation : 13-Jan-92 | Update : 06-Feb-94 |-* ATENF = 2* /* Attenuation factor */ not in use.* NORAG = 6000* /* ASP gain value */ min ASP gain for ASU calculation.; LASER = 00.05 /* Laser power mW */; CALRE = 9.0 /* Reference value of the calibration piece 25.0 */; COLQU = 0.0000000019 /* Collection Quality 1.9 nA/1REF/1mW */ PMT factor given by the vendor.* ELCFS = 3.0* /* Electronic full scale 3.0 */ not in use.; OPTTR = 0.52 /* Optical transmition */* KATOC = 0.00000005* /* Katod current nA */ PMT factor given by the vendor* SIGTN = 22.0* /* Signal to noise ratio 22.0*/ ASU formula variable DO NOT TOUCH* ANODC = 0.00025* /* Anode current uA */ ASU formula variable DO NOT TOUCH; FDRCO = 30.0* /* Fdr corection */ ASU formula variable DO NOT TOUCH* REFDQ = 1.2* /* REF FDR quality factor */ ASU formula variable DO NOT TOUCH.; MINSN = 16.0* ASU formula variable DO NOT TOUCH ; AVESN = 16.0* ASU formula variable DO NOT TOUCH ; PICSN = 16.0* ASU formula variable DO NOT TOUCH ; MIPTR = 0.000020* /* MInPowerToRuler */min. power to ruler for proper operation. not in use. ; RULTR = 0.056* /* RULlerTRansmision */; MINHV = 01 /* Range : from 00 to FF (Hex)*/ PMT table calibration will starts at.min control word for PMT high voltage in PMT calibration (600V).; MAXHV = FF /* Range : from 00 to FF (Hex) */ PMT table calibration will ends at. max control word for PMT high voltage in PMT calibration (1500V)./* NDF TRANSPARENT PARAMETERS */=; TNDF0 = 100.00 ; TNDF1 = 075.00; TNDF2 = 050.00; TNDF3 = 038.00; TNDF4 = 025.00; TNDF5 = 018.00; TNDF6 = 012.00 ; TNDF7 = 0