TDS-11S Training General Information TDS-11S Top Drive Sectional Guide Beam Transmission/ Motor Housing Rotating Link Adapter PH-50 Pipehandler AC Drilling Motors (2) Motor Cooling System Counterbalance System System Bail Washpipe Assembly Gooseneck (S-Pipe) 0 50 100 150 200 250 0 5,000 10,000 15,000 20,000 25,000 30,000 35,000 40,000 45,000 50,000 55,000 Rotating Speed (rpm) Torque (ft.lbs)800hp Version 700hp Version Torque/Speed Curves Typical Mast Interface Existing Travelling Equipment 500 ton Hook/Block Combo Type Crown Block Top Bail Rest Tool Joint 13.5 4.1m 13.5 4.1m 18.0 5.4m ClearWorking Height142.0 (43.3m)Drill Stand Made Up 4 (1.2m)93.0 (28.3m)To CL of Beam10.0 (3m)min.To Service Loop7.0 (2.1m) min.Drill Floor TDS-11S Varco Portable Top Drive System Sectional Guide Beam Assembled On Site Derrick Termination 80 (24.4m) Mud Hose Connected to Standpipe 73 (22.3m Level) Service Loop Portable Torque Reaction Beam U-Bolted to Spanners 2 x Custom Spanners On A-Frames or Mast Side Panels Varco Drillers Console Control Cable with Connectors 150 (45.7m) Unitized Variable Frequency Drive & Control Panel Power Supply AC Cables Power & Control Cables Typical Floor Layout Drillers Console Universal Spreader Beam Sectional Guide Beam Mast Saddle 80ft TDS-11S 86 Service Loop 75 Rotary Hose Rathole Mousehole Unit Identification Top Drive Identification Plate Located on the front of the motor housing Warning Label Located on the side of the bonnet Warning Labels Located on the side of each AC motor AC Motor Identification Label Located on the side of each AC motor Encoder Instruction Label Located on the side of the brake housing TDS-11S - Dimensions 28” 0.71m 56” 1.42m 62” 1.58m 18.5” 0.47m 214.0”5.43m120” Bail 88” Bail 112”2.85m233”5.82m72” 1.83m 37” 0.94m TDS-11S - Envelope 26” (660mm) 36.9” (937mm) 32.6” (828mm) 31.0” (787mm) 33.7” (856mm) 33.8” (859mm)32.0” (762mm)Standard Setback22.1” (660mm)21.1” (536mm)22.8” (579mm)Front Rear 350 or 400 hp AC Drilling Motor (2) Cooling System Air Duct (2) Drive Stem Gooseneck ( S-Pipe) Washpipe Packing Assembly Bonnet 钟型罩 10.5 : 1 Transmission Hydraulic Brake (2) Cooling Fan Motor (2) System Bail TDS-11S Power Train Bull Gear Main Shaft Assembly Transmission Motor Housing Main Body Transmission Housing Pinion Gears Spur Gears Louvers Motor Cooling System 5 HP AC Motors Centifugal Blowers AC Drilling Motors Intake Air Flow (Between Motor and Brake Housing Air Flow Air Ducting Exhaust Air Flow AC Drilling Motor Brakes Monthly Calipers & Pads Inspect Caliper Mounting Bolts (2) Steel Plate 0.09” AdjustCaliper Mounting Bracket Brake Pads Ac Drilling Motors Weekly Motor Cables Inspect Weekly Louvers Inspect Weekly Screens Inspect Air Inlet (550 CFM) Air Exhaust Motor Brake Motor Frame (Laminated) 机壳 Motor Shaft Pinion Gear Rotor Assembly (Laminated) End Coil Guide Roller Bearing 导向轴承 End Coil Stator Assembly (Laminated) 定子铁芯 Thrust Ball Bearing 推力轴承 Alternating Current Motor Motor Housing & Transmission Adjusting the Encoder(s) Encoder Belt Belt Tension Spring Belt Tension Spring Sled Hold-Down Screws (4) Sled Hold-Down Screws (4) Sled 滑撬板 Sled Electrical Connector On-Board Hydraulics Hydraulic Oil Filter Counterbalance Accumulator Upper IBOP Time Delay Accumulator Hydraulic Oil Fill Oil Pressure Switch System Accumulator IBOP Pressure Switch Upper IBOP Actuator Cylinder Counterbalance Manifold Main Hydraulic Manifold Link Tilt Manifold Link Tilt Cylinders Counterbalance Cylinders Hydraulic Oil Reservoir Rotating Head Motor and Shot-Pin Assembly Motor and Pump Assembly Reservoir Capacity 25 Gallons(114L) Pump Motor Specifications 10hp, 1,800rpm On Board Hydraulics Main Hydraulic Manifold Reservoir M 10hp AC Motor Variable Displacement Pump Fixed Displacement Pump SystemAccumulator IBOPAccumulator Counterbalance Accumulator Counterbalance Cylinders Counterbalance Manifold Drilling Motor Brake Shot-Pin Cylinder Rotating Link Adaptor Lift Rotating Head Motor Rotating Head Piphandler Clamp Cylinder Link-Tilt Cylinders Link-Tilt Manifold Upper IBOP Actuator Cylinder Lube Oil Distribution Hydraulic Motor Lube Oil Pump Sump Hydraulic System Maintenance Reservoir Bladder Blower & Brake Covers Oil Heat Exchanger Drill Motor Assy. (LHS) Monthly Oil Heat Exchanger Inspect Hydraulic System Maintenance Hydraulic Reservoir Bladder Reservoir Breather Reservoir Cover Gasket Hydraulic Oil Reservoir Reservoir Bladder Annually (年检 ) Reservoir Bladder Inspect Reservoir Bladder Hydraulic System Maintenance IBOP and Oil Pressure Switch IBOP Pressure Switch Configuration Oil Pressure Switch Configuration Pressure Adjusting Screw Wires Hoses Annually 年检 Hoses Inspect Annually Wires Inspect IBOP Pressure Switch 1500psi (102.0 bar) rising Oil Pressure Switch 18.0psi (+0/-1) decreasing Compone