资源预览内容
第1页 / 共10页
第2页 / 共10页
第3页 / 共10页
第4页 / 共10页
第5页 / 共10页
第6页 / 共10页
第7页 / 共10页
第8页 / 共10页
第9页 / 共10页
第10页 / 共10页
亲,该文档总共10页全部预览完了,如果喜欢就下载吧!
资源描述
Installation of EnkasonicEnkasonic现场安装案例说明用以下睡房的情况为例,简单地说一下Enkasonic隔振地台的干式安装:Illustration of Enkasonic installation (Dry Type):BathroomBedroom1 对楼板面的平整度进行初步评估,1平方米内不能超过5mm。如果地面过于粗糙不能满足施工要求,需要对表面进行找平处理。如下图:Check the floor smoothness. Roughness should be smaller than5mm within 1 sq.m.2平整度没问题后,就开始粘贴PEF3200围边胶。围边胶裁剪高度一般比楼板完成面高20mm,背面均匀涂上胶水,粘贴于墙身。如图:Clean the floor, cut the perimeter isolation strip into the appropriate size (Model: NOISESTOP PEF3200), in general the height should be20mm higher than the floor finish. Then, apply the glue at the back of isolation strip and adhere through wall.3做好围边胶后就开始铺放Enkasonic,白色纤维面向上。用Enkasonic一边多余的白色纤维面覆盖到另外一排Enkasonic上,再用皱纹胶纸粘贴紧,即可完成连接。如下图:Place Enkasonic over subfloor (or waterproofing membrane if applicable) with the black mesh down, white fabric side up.Tape sufficiently to prevent movement of the Enkasonic strips during construction.tape4铺排好Enkasonic后就开始,铺第一层GRC板,GRC板采用错搭法排布。并根据现场情况对GRC板进行切割,如下图:After the Enkasonic is installed, place one layer of GRC board on top of the matting. Then, place a second layer of GRC board. 4在板与板的接合处安装连接码,用铁钉把GRC板固定,絕對不能用硬物,例如釘,螺絲或金屬物件將圍邊或地臺上的Enkasonic E固定, 如下图:Apply the joining plates on every joining angle between the GRC panels.Do not penetrate into the Enkasonic with either wood screws or staples.512mm厚GRC板起码要铺排2层后,就可做表面的木地板或地砖饰面。在做好完成面后把多余的PEF3200围边胶割除,再打上非硬化密封胶即可。Install tongue and groove wood-floor on top of the floating 2-layer GRC board. Trim the excess PEF3200 perimeter isolation board. Apply sealant at the edge.备注:湿式安装(浇注混凝土方式)大致和上相同。在完成第三步后,在Enkasonic表面铺上0.2mm厚防水薄膜,再浇注混凝土,混凝土内部配直径2mm网格50x50mm的钢网。待混凝土凝固后可做饰面处理。Remarks: For wet type installation (concrete), after step 3, cover Enkasonic with a 0.2mm waterproof film, then, pour the concrete mortar bed, which supported by a 50x50mm2mm diameter gauge welded wire mesh.After the proper curing of the bed, install the ceramic or marble tile. By广州建声贸易有限公司技术部技术工程师黄善智/(Chris)Architectural AcousticsTechnical EngineerChrisAppendix: Common problems of Installation附件: ENKASONIC的安装应该注意避免以下问题1) 安装方向Installation Direction正确安装(白色纤维面向上) Correct Installation - white fabric side up错误安装(黑色纤维网面向上)Wrong installation Black mesh side up2) 地台四周需要用PEF3200围边胶隔离PEF3200 must be installed at the surrounding to isolated the floor system from the wall正确安装 Correct installation错误安装 Wrong installation3) 所有管线不能穿过地台的浮动层All pipes should not penetrate through the floating floor system正确安装 Correct installation错误安装 Wrong installation End _Architectural Acoustics (Holdings) LimitedTel:+852 2367 3232 Fax: +852 2724 8001Email:salesaa-hk.hk 10
网站客服QQ:2055934822
金锄头文库版权所有
经营许可证:蜀ICP备13022795号 | 川公网安备 51140202000112号