华为AP3010DN-AGN无线AP设定为一般胖AP无线路由器模式操作步骤说明文档1,认识硬件除以上之外，还需要普通网线1条，电脑1台。2,所用到的软件操作系统xp或win7Xmanager4汉化版USB转COM线驱动TFTP软件3CDaemon汉化版AP升级固件的文档FatAP3X10XN_V200R005C00SPC600.bin3,操作步骤： 第一步，复位AP，刷固件FatAP3X10XN_V200R005C00SPC600.bin第二步，登录AP的WEB管理页面创建WIFI并建立DHCP第三步，创建WAN口并与LAN口关联下面分步详细说明准备软件，依次安装USB转COM驱动，Xmanager4汉化版，将TFTP软件3CDaemon汉化版复制到C盘，并变更文件夹名称为TFTP，路径如C:TFTP ，把AP 的固件FatAP3X10XN_V200R005C00SPC600.bin复制到C:TFTP目录中给AP接上12V2A的电源，此时不要接POE供电模块，注意！复位后将消除全部配置及密码。等启动完毕后，用尖锐物按下复位口10秒后松开，AP开始重新启动，AP的指示灯变为长亮启动状态，之后指示灯变为闪烁状态完成复位。完成复位后接上USB 转串口线，连接电脑USB口和AP的Console口，打开Xmanager4中的Xshell4，新建会话窗口选择SERIAL配置波特率9600及COM端口号正确连接成功后会显示Please configure the login password (/)Enter password:这是初次登录要求设定密码，密码复杂度要求为英文加数字，最小8位，我们暂定密码hua88888填写两次密码后显示如下Enter password:Confirm password:这表示已经成功设定了管理密码，以上设定的密码仅限于连接Console口使用，和WEB管理界面不是同一个密码，WEB管理界面密码下面会提到。使用1条一般使用的网线，一端连接电脑，一端连接AP的ETH/PoE口，此时不要拔掉Console口上的串口线，不要拔掉12V电源，不要连接POE供电模块，配置电脑有线网卡的IP地址为169.254.1.100子网掩码255.255.0.0网关169.254.1.1 DNS空白不填写，去我的电脑打开C:TFTP目录，打开3CDaemon.EXE点击设置TFTP服务器按钮，按照下图设置路径然后回到Xshell4窗口，会显示Please check whether system data has been changed, and save data in timeConfiguration console time out, please press any key to log on是因为超时登出，需要重新填写密码登录，重新登录后按照以下脚本操作，整个过程不要关闭3CDaemon.EXEsys #键入Enter system view, return user view with Ctrl+Z.Huaweiap-mode-switch prepare #键入Info: Prepare is ok, Use ap-mode-switch command to switch to fit ap.Huaweiap-mode-switch check #键入Info: Ap-mode-switch check ok.Huaweiap-mode-switch tftp FatAP3X10XN_V200R005C00SPC600.bin 169.254.1.100 #键入Info: Preparing to upgrade. Please wait a moment .Warning: System will reboot, if you want to switch to upgrade-assistant-package.Are you sure to execute these operations ? Y/N:y #这里是提示整个过程会重启，键入yInfo: system is rebooting ,please wait.Try hardware rebooting. * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * Welcome To HUAWEI AP World UBoot V200R005 version-125 (Aug 1 2014 - 04:33:21)DRAM: 128 MBDDR data bus test is OK!Press c or C to Begin DDR Bus Test in 1 Seconds: 0 Flash: 32 MBPCIE: PCIe Clock 40MHzEthernet Mac: B4-15-13-F8-82-20Image: Current Bootup is B Image: Current Bootup is B Current master bootup parameter area is ABoot Kernel A Address: 0x9f3fb000Boot Kernel B Address: 0x9fPress j or J to stop Bus-Test in 1 seconds: 0Bus test starting.PCIE bus test OK.SPI bus test OK.DDR bus test OK.RGMII bus test OK.Bus test ending.Save Bus Test Result SuccessfulPress f or F to stop Auto-Boot in 3 seconds: 0 Uncompressing Kernel Image . OKStarting kernel .Booting Atheros AR934xinit_bsp_adapter .OK.mm_init .OK.sched_init .OK.softirq_init .OK.console_init .OK.thread_info_cache_init .OK.fork_init .OK.dbg_late_init .OK.imv_init_complete .OK.Linux version 2.6.34.13-WR4.3.0.0_standard (gcc version 4.5.2 (Sourcery CodeBench Lite 2011.03-93) ) #2 PREEMPT Fri Nov 7 17:34:15 CST 2014flash_size passed from bootloader = 32 MBarg 1: console=ttyS0,9600arg 2: root=/dev/mtdblock10arg 3: rootfstype=squashfsarg 4: init=/sbin/initarg 5: mtdparts=ath-nor0:512k(BiosA),128k(BootupA),128k(BootupB),128k(BootEnv),128k(BoardData),12288k(SysImageA),3072k(configA),512k(BiosB),128k(ResultA),128k(ResultB),12288k(SysImageB),3072k(configB),256k(ArtArgs);arg 6: mem=126Math_sys_frequency: cpu apb,ddr apb,cpu-480MHZ,ddr-400MHZ,ahb-240MHZZone PFN ranges: Normal 0x - 0x00007e00Movable zone start PFN for each nodeearly_node_map1 active PFN ranges 0: