工时定额二、常用机床的工时定额（一） 截锯定额1、方材类 定额(块/小时)料长（mm）料厚（mm）15以下16252635365051以上250以下140011001000820670250500120010009008006505107501000900750700500760100090070070060045010101250800650600500330126015006506005004103001510175060050445636027017602000576432403288220201022505043603002161602250以上4562882401441002、板面类 定额 (块/h) 料长(mm)料宽（mm）70以下70120121200201300301400401550551750701900900以上250以下100078065040029021017015011525150085070050032023015012010090510750760600400230153140130115807601000570450310210140130120807010101250450380250180115110908063126015004003602301609085806257151017503803002101408075705752176020003502502001157065605246201022502302001509060555046372250以上180140120805044403732(二)小带锯定额1、方木类 定额（块/h）料长（mm）厚度（mm）20以下21303140415051以上100以下15001100975850620250400120085082580055040060010006505254003206007507804303502802507509005004003002602009001050450335280220170105012004002702201801502、板面类 定额 (块/h)长度(mm)宽度（mm）70以下70120120200201300301400401550551700701900900以上250以下8605003001901301006755422504003031020011090726248364006006702801901008167554233600750600240175906858453530750900500180160755852443428900105044016014570484438322610501200370145130653826333025说明：板面类以厚度1530mm为计算单位，如30mm以上厚板应减完成量20%，15mm以下的加完成量的20%。（三）纵解圆锯定额1、方木类 定额料长宽度（mm）20以下21303140415051以上250以下130010009806304002514001000740670500350401550860610550430330551750600480440350300751100050034031026020010011250460300270230180125115003602602201601501501175031024020013012017512000260180160100902001225024013012085742251以上1901101007060说明：1、方木以一块加工一次为计算单位。如一块加工两次按二次计算。 2、小料150mm以下的连接料如不是固定长短，则按250mm以下计算。 3、大小头腿子都以每块加工二次计算。如加工一次减完成量40%。2、板面类 定额料长宽度（mm）70以下71120121200201300301400401550551700701900900以上250以下110053031022013010085675525150095038024014097857555425017508303502201108572654536751100068026018595656055423210011250520200140804845403530125115004301701207340353030271501175035014410555323028262417512000300100854230282625232001225024095603628242322202251以上1758544282322201918说明：1、方木类以一根锯一面为计算标准，若一根锯两面算二根。 2、板面类的厚度以15mm至30mm为标准，若厚度在30mm以上的减定额数的20%，15mm以下的加定额数的20%。 3、纵解圆锯用于截断时，按截锯定额计算，并减去定额30%。（四） 平刨定额1、方木类（加工一个大面和一个小面） 定额料长30mm以下3150517071以上250以下0.170.190.210.272513500.200.200.250.323514500.230.260.290.374515500.250.270.320.415516500.260.320.370.446517500.290.360.420.457518500.360.450.490.558519500.440.500.550.6395110500.470.530.600.69105111500.500.580.650.75115112500.520.620.710.83125113500.560.680.750.87135114500.580.750.790.95145115500.620.790.870.99155116500.650.830.921.01165117500.680.870.961.06175118500.750.921.051.25185119500.790.961.121.31195120500.830.991.211.39205121500.891.011.281.50215122501.001.161.341.56225123501.071.231.371.67235124501.101.311.421.752451以上1.561.751.841.972、板材类（加工一个大面、一个小面） 定额板长(mm)板宽(mm)30mm以下3150517071以上250以下0.240.290.310.322513500.290.310.340.383514500.350.380.360.394515500.360.490.520.525516500.420.520.560.566517500.500.600.620.657518500.520.620.650.688519500.560.680.710.7595110500.620.790.810.83105111500.680.840.910.94115112500.710.850.991.03125113500.791.031.061.08135114500.831.061.101.16145115500.871.071.121.17155116500.931.121.161.19165117500.991.211.251.29175118501.061.281.311.39185119501.121.311.371.42195120501.211.421.441.47205121501.281.531.561.60215122501.311.601.631.67225123501.371.671.701.7523512450