Sawdust crusher Structure and operating principle This machine is combination crusher, stop cutting machine, slice and crushing the first cutting into the crushing, by the hammer piece at high speed, and the wind screen send out material mouth, a become particles. Sawdust crusher instructions 1, switch on the power, to see whether it is right. 2, put in cutting tools, blade knife dish out planar 2-4 mm, and then lock down the bolt. Such as the discovery of pressure bolt thread is wear, should be replaced immediately, in order to prevent caustic slide the knife dish nut. 3, change the sword expansion degrees, must be stretched the length of the sword consistent. 4, by the sword length, particles of less than ideal, change of different diameter luo sieve 5, it is strictly prohibited to carry the stone, nail wood into machines, in case of a break in a sword and 6, check hammer piece of bolt, found loose, immediately tighten, hammer slice and bolt wear serious when, should be replaced. 7, sharpening Angle for the straight line 28-30 , forbidden ground into raised face, raised face can lead to steel blade from or local jie steel. 8, often use machines should check whether the bearing grease lack. Should be 3-4 hours raises a butter, charging too much butter not easily. Sawdust crusher Method of use 1, this machine use, do not change the power and speed, Angle grinder, straight line kept the original 28-30 . 2, change, grain, needs a new ROM, blade adjustment simultaneously, LuoKong minimum not less than 14 mm (diameter), the biggest not more than 20 mm (diameter), and the sword length 3-6 mm, the bottom of the knife knife plate and the gap is not more than 1 mm. 3, the machine can powder 3 cm in diameter-20 cm of the wood into granular. 4 The quality of incoming material feeding port the biggest diameter is 300 mm. If wood diameter feeding port more than the biggest diameter, can use the form a complete set of firewood machine to split wood, in the smash. Sawdust crusher troubleshootingFault phenomena Fault reason Elimination methodLow yield(1) the blade is not sharp; (2) the blade did not adjust good, cut out of wood a granular The grinding blade Feeding difficult1) the blade wear not sharp; (2) the fixed knife gap is too small or too large(1) the grinding blade; (2) adjust the fixed knife clearance 2-3 mm; (3) the blade Angle is not greater than 30 degrees Load super jose (1) feeding uneven too fast; (2) the blade is not sharp (1) reduce feeding speed; (2) the grinding blade Bearing heating (1) in the bearing no butter; (2) with the bearing not flat; (3) bearing damage; (4) belts tight 1) bearings inside and butter; (2) the housing balance; (3) change new bearing; (4) reasonable adjustment belt. Sawdust crushe parametersKnife roller diameter (mm 800Number of round ( 2The feeding port size (mm) 310*680Knife roller speed (turn/points)650Feeding speed (m/min 35/37.38Raw material processing the biggest diameter (mm) 300Wood length (mm15-35Production capacity (m3 / h) 15-35The main motor power (kw)110Feed roller motor power (kw) 2*4Weight (t) 7Size (long * high * wide) (mm) 4670*2150*1500 木屑粉碎机(木材粉碎机)结构及操作原理该机系组合型粉碎机，止切削机、切片及粉碎先经切削进入粉碎，由锤片高速运转，风力经筛网送出料口，一次成为颗粒。木屑粉碎机(木材粉碎机)使用说明1 、接通电源，看转向是否正确。 2 、装换刀具时，刀口伸出刀盘平面24mm，然后拧紧螺栓。如发现压力螺栓丝扣磨损，应立即更换，以防损滑刀盘螺母。 3 、改变刀的伸缩度，必须是伸刀长短一致。 4 、靠调刀长度，颗粒达不到理想时，改换不同孔径的罗筛。 5 、严禁夹带石头、钉子的木柴投入机内，以防打坏刀个和内件。 6 、注意检查锤片螺栓，发现松动，立即紧固，锤片和螺栓磨损严重时，应更换。 7 、磨刀角度为直线2830，严禁磨成凸面，凸面会导致钢刃脱离或局部揭钢。 8 、经常使用的机子应检查轴承黄油是否缺少。应34小时加注黄油一次，加注黄油不易过多。木屑粉碎机(木材粉碎机)使用方法1 、本机使用，不改变动力和速度，磨刀角度，保持原来直线 2830。 2 、改变颗粒，需换罗、调刀同时进行，罗孔最小不小于14mm（直径），最大不大于20mm（直径），调刀长度36mm之间，底刀板和刀的间隙不大于1mm 。 3 、该机能粉直径3cm20cm以下的木料成颗粒状。木屑粉碎机(木材粉碎机)故障排除故障现象故障原因排除方法产量较低刀片不锋利；刀片未调整好，切出木屑不成颗粒状修磨刀刃进料困难刀刃磨损不锋利；定刀的间隙太小或太大修磨刀刃；调整定刀间隙2 3mm ； 刀片角度不能大于负荷超荷进料太快不均；刀片不锋利降低进料速度；修磨刀轴承发热轴承座内无黄油；轴承座未装平；轴承损坏；皮带过紧轴承内加黄油；轴承座校平衡；换新轴承；调整皮带松紧。技术参数刀辊直径（毫米）800飞刀数（片）2进料口尺寸（毫米）310*680刀辊转速（转/分）650进料速度（米/分）35/37.38加工原料最大直径（毫米）300木片长度（毫米）15-35生产能力（立方米/小时15-35主电机功率（千瓦）110喂料辊电机功率（千瓦）2*4重量（吨）7尺寸（长*高*宽）（毫米4670*2150*1500棕榈树粉碎生产线