通讯二层网管型交换机常用功能设置方法（目前适用机型：S4108M、S2916F1、S2924F1、S2924F2、S2924G2）一、 进入交换机1、 通过CONSOLE口进入：设置速率：9600 数据位：8 奇偶校验：无 停止位：1 数据流控：无。 设置正确后，开机显示类似如下界面：POST version 2.00 = enter C to abort booting within 3 seconds .booting .Start to run system initialization task.System ConfigurationCompany Name : TCLCOMMModel Name : S2916F1Board Name : Rev1.20MAC Address : 00-0E-1F-57-14-91TCL Telecommunication Equipment (Huizhou) Co. Ltd.Firmware version: V3.03Press key to start.回车后输入默认用户名：admin，默认密码：123；输入enbale进入特权模式。如果忘记用户名和密码，则用特权用户名：tcl，特权密码：MAC地址后6位（启动界面有显示交换机MAC地址）2、 TELNET进入： 将PC配置和交换机一个网段，交换机出厂默认IP是192.168.2.248，在DOS窗口下输入TELNET 192.168.2.248，Default user：admin Default password：123。输入enbale进入特权模式。3、 Web界面：将PC配置和交换机一个网段，交换机出厂默认IP是192.168.2.248，在IE地址栏下输入192.168.2.248, Default user：admin Default password：123。输入enbale进入特权模式。二、 设置过程1、 常用查看命令S2916F1#?Command List?. Help commandsbackup. backup run-time firmware or configuration fileconfigure. Enter configuration modedisable. Turn off privileged commandsexit. Logoutfind. Find commandshelp. Help commandslogout. Logoutping. Ping a specified host with IP addressreset. Reset system or reset factory default settingshow. Show commandsupgrade. Upgrade run-time firmware or configuration fileS2916F1#show system System Configuration Company Name : TCLCOMM Model Name : S2916F1 Board Name : Rev1.20 Firmware Version: V3.03 MAC Address : 00-0E-1F-57-14-91S2916F1#show ip eth0 Network Configuration: IP Address: 192.168.2.248 Netmask : 255.255.255.0 Gateway : 192.168.2.1 S2916F1#show run eth0 Network Configuration: IP Address: 192.168.2.248 Netmask : 255.255.255.0 Gateway : 192.168.2.1 802.1Q Configuration 802.1Q setting : Enabled Port Vlan Configure PVLAN Setting: Disabled Spanning Tree Configuration SPT Setting : Disabled Multicast Configuration Press to continue . or Press to abort! Multicast Setting : Disable IGMP Configuration IGMP Switch : Disabled Trunk Group Configuration Trunk Setting: Disabled Mirror ConfigurationMirror Switch:Disabledstorm-control ConfigurationStorm-control : Disabled ! (for every port)QoS ConfigurationPress to continue . or Press to abort!Qos setting : DisabledIP ToS ConfigurationTos setting : DisabledPort Protect ConfigurationPort Protectl : Disabled !(for every port)mac-address-security configurationmac-address-security : Disabled !(for every port)PING64 bytes from 192.168.2.1, icmp_seq=0, time=10ms64 bytes from 192.168.2.1, icmp_seq=1, time=10ms64 bytes from 192.168.2.1, icmp_seq=2, time=10ms64 bytes from 192.168.2.1, icmp_seq=3, time=10msSent Packets: 4 Got Good Packets : 42、 设置端口限速S2916F1(config)#interface ethernet 0/8 (进入端口8设置模式)S2916F1(config-if)#egress 2000K (设定出口速率为)Set port egress rate successful!S2916F1(config-if)#ingress 1500K (设定入口速率为1.5)Set port ingress rate successful!如需取消端口限速，则将端口出、入口速率改回100000K即可。3、 设置生成树S2916F1(config)#spanning-tree enable （启用生成树）Enable Spanning Tree function successful!S2916F1(config)#spanning-tree disable （关闭生成树）Disable Spanning Tree function! 4、 设置广播风暴拟制S2916F1(config)#interface Ethernet 0/10 (进入端口10设置模式)S2916F1(config-if)#storm-control level 20 （设置该端口保留2的广播包，丢弃80）Successful to set broadcast storm-control! （广播风暴抑止比例有3.3/5/10/20/100等5种）S2916F1(config-if)#storm-control level 100 （取消广播风暴抑止设置）Successful to set broadcast storm-control!5、 设置基于端口的VLAN1） 快速端口隔离（指定一个上联端口，执行命令后其他端口之间全部隔离）S2916F1(config)#port-protect 8 （设置口为上联口，其他口之间隔离）Set port-protect successful!S2916F1(config)#port-protect disable （取消快速端口隔离设置）Set port-protect successful!2） 根据具体需要手动指定每个PORT VLAN的端口数量S2916F1(config)#pvlan ena （先在全局模式将port vlan功能打开）Port vlan enabled successful!S2916F1(config)#inter ether 0/1 （再进入端口